LEAN AUDIO No.1 for PA Loudspeakers, Guitar Speakers, Bass Guitar Speakers & HI FI speakers

18 Sound 10CX650 10" 1" High Performance Coaxial

£261.58

Quantity:

Eigtheen Sound 10CX650 10" 1" Coaxial speaker 8ohm
The 10CX650 is a 10" - 1" coaxial transducer designed for use in compact reflex enclosures and stage monitors as small as 30 lt, with a nominal dispersion of 90 degrees.


94.0 dB LF/106.5 dB HF SPL 1W/1m average sensitivity
Single magnet motor
400W LF - 140W HF maximum program power handling
65 mm (2.5) LF voice coil
44 mm (1.75) HF PEN diaphragm
Proprietary Phase Plug design
HF copper sleeve for reduced distortion and higher output
90 degrees nominal conical dispersion
Atmos ready*
Extended LF design
Suitable for very compact enclosures and stage monitors


LF General Specifications

Nominal Diameter
260 mm (10 in)
Rated Impedance
8 Ohm
AES Power
400 W
Program Power
800 W
Peak Power
1600 W
Sensitivity
94 dB
Frequency Range
60 ÷ 4800 Hz
Power Compression
@-10dB 0,3 dB
Power Compression
@-3dB 1.3 dB
Power Compression
@0dB 2.3 dB
Max Recomm. Frequency
1500 Hz
Recomm. Enclosure Volume
25 ÷ 45 lt. (0.88 - 1.59 cuft)
Minimum Impedance
6,1 Ohm at 25°C
Max Peak To Peak Excursion
26 mm (1 in)
Voice Coil Diameter
65 mm (2.56 in)
Voice Coil Winding
Material Edgewound copper
Suspension
Double roll, Polycotton
Cone
Curvilinear composite

Thiele Small Parameters

Fs 54 Hz
Re 5.1 Ohm
Sd 0,0346 sq.mt. (53.63 sq.in.)
Qms 5.90
Qes 0,39
Qts 0,35
Vas 36.4 lt. (1.29 cu.ft)
Mms 39.5 gr. (0.09 lb)
BL 14 Tm
Linear Mathematical Xmax ± 6mm (±0,24 in)
Le (1kHz) 0.90 mH
Half space efficiency 1.5 %


HF General Specifications

D.C. Resistance
5.3 Ohm
Continuous Power
70W above 1,1 kHz
Max. program power
140W above 1,1 kHz
Sensitivity
106.5 dB
Frequency Range
900 - 15000 Hz
Min Xover Frequency
1.5 kHz
Diaphragm material Pen
Voice Coil winding material Edge-wound aluminum
Voice Coil Diameter 44mm

Overall diameter 260 mm (10.24 in)
N. of mounting holes and bolt
8
Mounting holes diameter 6.1 mm (0,24 in)
Bolt circle diameter
243.5 - 246.5 mm (9.59 - 9.70 in)
Front mount baffle cutout
230 mm (9.06 in)
Rear mount baffle cutout
231 mm (9.09 in)
Total depth
155 mm (6.10 in)
Flange and gasket thickness
8.9 mm (0,39 in)
Net weight
6,8 kg (14,99 lb)
Shipping weight
6,8 kg (14,99 lb)
CardBoard Packaging dimensions
280 x 280 x 170 mm (13.07 x 13.07 x 7.24 in)

The 10CX650 is a 10" - 1" coaxial transducer designed for use in compact reflex enclosures and stage monitors as small as 30 lt, with a nominal dispersion of 90 degrees.

The high force ceramic single magnet structure makes the 10CX650 a lightweight speaker for its performance class - only 6 kg (13.2 lb). The 65 mm (2.5 in) LF edgewound CCAW voice coil employs our Interleaved Sandwich Voice coil (ISV) technology, in which a high strength fiberglass former carries windings on both the outer and inner surfaces to achieve a balanced coil with a uniform distribution of mass and motion energy. This results in an extremely linear motor assembly. The low profile curvilinear LF cone provides a smooth response within its intended frequency range and maximum reliability under high mechanical stress.

Equipped with a proprietary hybrid radial tangerine phase plug, the integrated HF compression driver has been designed to give smooth coherent wavefront at the horn entrance in all working frequency ranges with a high level of manufacturing consistency. The phase plug, with its short openings and high flare rate value, assures low distortion and remarkable improvements in mid-high frequency reproduction. A copper sleeve reduces inductance values above 10kHz, improving phase and impedance linearization.

The HF diaphragm assembly is made with a proprietary treated Polyethylene material. Thanks to its superior diaphragm dimensional stability, the polyethylene shows consistent behavior throughout its whole working life. Moreover, this particular material with its very high value of elasticity modulus is capable of superior transient and intermodulation distortion response. The flat suspension shape is designed to maintain low stiffness and low mid band distortion and response. An edge-wound aluminum voice coil wound on proprietary treated Nomex completes the diaphragm assembly. Thanks to its physical properties, the proprietary treated Nomex former shows a 30% higher value of tensile elongation at a working operative temperature, when compared to Kapton. This feature enables proper energy transfer control from the voice coil to the dome in real working conditions. Moreover, this former material is suitable for use in damp and wet environments. A specific dedicated HF driver throat design has also been chosen, maximizing the cone’s profile coupling.


Please Choose:



  • 2 Units in Stock